How To Flush A Breville Barista Pro?

How To Flush A Breville Barista Pro

Sharing is caring!

Keeping your Breville Barista Pro running like new takes more than just a little bit of elbow grease. You need to know how to properly clean it and care for all of its parts. In this article, we’ll show you how to flush your machine and keep it running like new.

What is the purpose of flushing the Breville Barista Pro?

When you press the flush button on your Breville coffee machine, all of the water in the tank is forced through the coffee grounds and into your cup. This helps to create a richer, more flavorful cup of coffee.

In this article, we’ll show you how to flush your machine and keep it running like new.

What Is the Breville Barista Pro?

What Is the Breville Barista Pro?

The Breville Barista Pro is a semi-automatic espresso machine that has a built-in grinder.

It’s popular with home baristas because it allows them to grind the beans and make the espresso right in the machine.

This is a big plus over machines that require you to grind the beans before you make the espresso.

The Barista Pro also has an automatic milk frother.

This means that you can make lattes and cappuccinos with the touch of a button.

It also has a built-in water tank, so you don’t have to worry about refilling it frequently.

What Does It Mean to “Flush” a Breville?

What Does It Mean to "Flush" a Breville?

Flushing a Breville espresso machine is a way of cleaning it and preparing it for use.

It’s important to do this on a regular basis to keep the machine running smoothly and to ensure that your coffee comes out tasting its best.

The process of flushing a Breville is simple: just fill the water tank with hot water and insert the cleaning tablet.

Close the steam wand and run the machine for a few seconds.

Open the steam wand and let the water run through.

Close the steam wand again, wait for the beep, and then unplug the machine.

It’s a good idea to flush your Breville espresso machine every time you change the coffee beans, or at least every other time.

This will help keep the machine in good condition and ensure that your coffee always tastes its best.

Why Should I Flush My Breville Barista Pro?

Why Should I Flush My Breville Barista Pro?

To keep your Breville Barista Pro functioning flawlessly, flush it frequently.

By flushing it, you’re removing any built-up oils and residue that can cause the machine to run inefficiently.

Not only will flushing your machine help it run better, but it’ll also help preserve the flavors of your coffee beans.

Over time, those oils and residues will start to affect the flavor of your coffee, so it’s important to get rid of them regularly. 


Step-by-Step Guide to Flushing Your Breville Barista Pro

Step-by-Step Guide to Flushing Your Breville Barista Pro

Now that you’ve read up on why flushing your Breville barista is so important, it’s time to get down to the nitty gritty of actually doing it.

Worry not, it’s really quite simple! Here’s a quick step-by-step guide:

  1. Make sure your espresso machine is off and all removable parts are detached.
  2. Fill the water tank up with freshly distilled water.
  3. Insert a cleaning disk into the group head and press deactivate.
  4. Turn on the power switch and allow all the water to flush through.
  5. When the cycle is complete, turn off the computer and remove the cleaning disk (properly discard).
  6. Refill the water tank with fresh distilled water and turn it on again, allowing all of it to flush through until it is empty.
  7. Turn off the power to your espresso machine.
  8. Reattach all removable parts and enjoy making coffee again!

How to Clean and Backflush a Breville Barista Pro

How to Clean and Backflush a Breville Barista Pro

To pull a great shot of espresso, several things must come together.

When trying to do that, we frequently concentrate on things like selecting the ideal bean, achieving the ideal grind, administering the ideal dosage, tamping evenly at the ideal pressure, and the list goes on.

The cleanliness of the machine used and how that contributes to even extraction and a clear taste

In our opinion, this is the most overlooked element in the fabrication of a good cup.

Far too often, when tuning up a machine, we glance inside the group head and roll up our sleeves.

And get ready to fight the scourge of 2 or more years’ worth of accumulated coffee grounds that have contaminated the taste of the remaining steps of our carefully controlled procedure for making espresso.

We’re going to show you how to spend five minutes with your machine to clean the group head and make better espresso at home.

Backflushing with water and detergent is where we want to start.

If you can only manage once a week, that is OK as well.

I advise a water backflush on whatever day the machine is used.

On all machines, we advise detergent backflushing once every two weeks.

With the exception of those that employ E61 group heads, for whom I once every one to two months.

The steps:

  1. Add up to a half-teaspoon (3 g) of Full Circle wash or espresso cleaning tablets after inserting the blind filter (only use Full Circle for detergent backflushing). Your portafilter must be secured to the group head.
  1. Ten seconds into the brew cycle, start the machine’s pressure release. Depending on how filthy your group head is, repeat 5-8 times.
  1. Take the portafilter out. Start the brewing process and rinse the portafilter under the grouphead’s water stream. cycle halt
  1. Put in a blind filter. Once more, lock your portafilter into the group head when using a clean blind filter devoid of the cleaner. To make sure there is no detergent residue remaining, repeat Step 2 after rinsing.
  1. Make a shot of espresso, then put it away (only for detergent backflush).
  1. Filters and the metal portion of the portafilter should be soaked in hot water with 1 teaspoon (6 g) of Full Circle powder for 30 minutes (but not the plastic handle).
  1. Restore the filters after rinsing with water (only for the detergent backflush).

Even a backflushing procedure can’t get rid of everything on the other side of your dispersion screen.

So if you add backflushing to a monthly maintenance schedule, the extra five minutes you spend giving your machine some love can save both your taste buds and your cash.

However, a little cleaning or a new dispersion screen can drastically improve the quality of the cup your machine produces.

Performing the straightforward step of removing your dispersion screen and cleaning your machine once a week as part of maintaining your machine and brewing high-quality espresso

The removal, cleaning, and reinstallation of various types of screens will all be covered below.

Remove the screen.

Machines hold their dispersion screen in place in various ways using a central hex screw.

The center of the screen is held in place by a hex screw on several espresso machines, including the A53 and Vivaldi. With those machines.

You can use the proper size wrench—7 mm for La Spaziale machines—to loosen the nut.

And once it is loose, you can manually unthread it to remove the screen along with it.

Other machines, such as the La Marzocco and Slayer, feature a flat head screw that holds their screens in place.

To start unthreading the screen, you must use a short, flat head.

Once it is loosened, you may also manually unthread it the remaining distance, and the screen will release along with the screw.

Gasket tension: The screen is kept slightly differently in each machine employing the E61 group.

E61s lock the screen in place using the tension of the group gasket rather than a screw to secure everything.

The edge of the group head can be used as countertorque to free the screen from its holding position while you pry out the screen and gasket with a flathead screwdriver to remove an E61 screen.

Scrub the screen.

After removing your screen, thoroughly scrub the inside of your group head and screen to eliminate all the accumulated filth.

We advise using a Pallo brush and a warm, moist rag to remove all the buildup that is not wanted in your group.

The rag will assist in removing any debris and/or hardened coffee grounds from the group head and screen.

Give the screen and group a thorough scrub with a brush after cleaning them with a rag, and then use the rag to remove any remaining grime.

I strongly advise against using a brush with firm bristles on the screen because doing so can result in inconsistent water dispersion.

Give you channeling every time you pull a photo with that screen in place.

Some machines include an external dispersion screen and a removable internal dispersion plate.

Both of these plates need to be cleaned because they might accumulate coffee grind over time.

Even with frequent cleaning, your machine’s screen should be replaced every one to two years because it will eventually wear out.

The two screens on the La Spaziale A53 and Vivaldi are the only exceptions to this rule.

As long as they are correctly cleaned with a gentle brush and are not bent when being reinserted into the group, they are known to distribute water equally for years.

Reinsert screen

After your group’s interior and the screen are spotless, you can reinstall the screen using the same procedure you used to remove it.

We advise tightening the screw as tightly as you can with your hand and checking the flow from the group head to make sure it is even when reinstalling a dispersion screen on a machine that has a screw that keeps it in place.

Typically, these screws shouldn’t be tightened any farther than hand tight because doing so could cause the screen to warp, irreversibly damaging them.

However, if you see uneven flow from the group after just hand-tightening the nut, go ahead and tighten it a half turn at a time before testing the flow through the screen once more to ensure it is even.

For E61 groups, i advise reseating the gasket and screen using a food-safe lubricant, such as Molykote 111, on the gasket.

Rejoice in the crisp, clear flavor you helped your machine generate now that you’ve cleaned your group’s head!

Need to Replace Parts? Here’s What You Need to Know

Need to Replace Parts? Here's What You Need to Know

If you’re looking to replace parts for your Breville Barista Pro, you may have some questions. That’s totally understandable!

You want to make sure you get the right fit and that it works with your machine.

First, check out the manufacturer’s website to see what parts they offer.

This will give you an idea of what’s available and the best parts to choose from.

Second, when ordering parts online, make sure that the seller is reputable and offers a warranty in case something isn’t right.

Check it out here: Breville Espresso Machine Parts

Finally, be sure to install any new parts correctly for optimal performance.

If it’s a complicated install, consider hiring a professional to make sure it gets done correctly and safely.

This will help ensure that your Breville Barista Pro runs like new for a long time!

Troubleshooting Common Breville Barista Pro Issues

Troubleshooting Common Breville Barista Pro Issues

If you’re having trouble with your Breville Barista Pro, try troubleshooting some of the common issues first.

If you don’t already have a solution, the next step is to contact a service representative.

One issue that can easily be fixed at home is poor pressure from the espresso machine.

Usually this means that the machine needs to be descaled, which is a process of removing calcium deposits.

other impurities from the machine using a descaling solution.

To do this, simply follow the descaling instructions in your product manual.

If your coffee does not come out hot or tastes weak, this could indicate that the boiler needs to be replaced or cleaned out.

Again, refer to your product manual for instructions on how to do this safely.

If all these steps fail, then it’s time to contact an authorized service representative for assistance.

It’s always better to get help from someone who knows what they are doing rather than try to fix something yourself and potentially cause further damage.

Breville Coffee Machine Flush Tablets

Breville Coffee Machine Flush Tablets

The Breville coffee machine flush tablets are made to maintain the cleanliness and functionality of your coffee maker.

These tablets are simple to use and will help your coffee maker last longer.

These tablets make cleaning your machine quick and simple and are made exclusively for Breville coffee makers.

Place one tablet in the water reservoir of your machine and start a brew cycle to use Breville coffee machine cleaning tablets.

The tablet, which also includes the brew basket and carafe, will dissolve and clean the entire device.

You might need to use two pills to clean your machine if you have hard water.

Additionally, if you haven’t cleaned your machine in a while, you might need to run a few brew cycles to completely remove the buildup.

How Do You Use Tablets for Cleaning a Breville Espresso Machine?

How Do You Use Tablets for Cleaning a Breville Espresso Machine?

Just insert a tablet into the portafilter and use the machine as usual to filter water.

As it passes through, the tablet will dissolve and clean the machine.

Since every manufacturer has their own set of standards, it is essential to read the user manual for each product.

It will take longer for the tablet to dissolve if you use a larger tablet than the manufacturer suggests.

Another risk is that a big tablet will become stuck in a tiny compartment that might not be big enough.

Cleaning tablets might not be usable if your machine lacks a bypass section.

In rare instances, you may need to manually rinse the brew unit in the sink if you must remove it.

Typical cleaning processes last 10 to 15 minutes.

What cleaning products ought you to employ? For guidance, see our chart.

Without reading the manual, many people assume that flushing is difficult. My suggestion is to read and take action.

How To Flush Breville Barista Pro Without Tablets

How To Flush Breville Barista Pro Without Tablets

You must take the coffee grounds and filters out of your Breville Barista Pro in order to flush it without tablets.

To remove any coffee residue, run a clean water cycle through the appliance.

Finally, use a moist towel to clean away any remaining coffee grounds from the machine’s surface.

Breville Barista Pro Flush Water Coming Out Of Portafilter

Breville Barista Pro Flush Water Coming Out Of Portafilter

It’s crucial to flush water through your Breville Barista Pro when you first get it to clean it out before using it.

Put a cup underneath the portafilter, start the machine, and let the water pass through it until clear water emerges.

It’s possible that there will be some silt in the water at first, but this is typical and will go away shortly.



So if you’re having problems with your Breville Barista Pro, or you just want to make sure it’s running like new, it’s important to know how to flush it. This quick and easy guide will show you how to do just that.


Where can I download the Breville Barista Pro machine manual?

You can download a copy of the machine’s manual here: Download Barista Pro User Manual

Sharing is caring!